+90-(216)-593-04-74
info@bimekscelik.com
  1. Ana sayfa
  2. Ürünler
  3. Özel Çelikler

Özel Çelikler

Farklı kullanım alanlarına sahip özel çelikler

Özel çelikler, birçok farklı alanda kullanılmak üzere tasarlanmıştır. Burada belirtilen ürünlere ek olarak, gelen talepler doğrultusunda farklı ürünlerin üretimi de yapılabilmektedir.

Özel çelikler için uygulanan ısıl işlemler talep edilen kalitelere göre değerlendirilmelidir.

Üretim Aralığı

  Uygulama Profil Aralık
[mm]		 Yüzey Tolerans
Çubuk Sıcak Haddelenmiş Yuvarlak 20-200 İşlem Görmemiş
Kabuk Soyulmuş		 –
Soğuk Çekilmiş Yuvarlak
Altıköşe
Kare		 3-70
3-70
4-60		 Parlak EN 10278
h9
h10
h11
Kabuk Soylumuş
Sıcak Haddelenmiş		 Yuvarlak 20-100 Parlak EN 10278
h9
h10
h11
Taşlanmış Yuvarlak 50-60 Parlak EN 10278
h7
h8
h9
h10
h11
Kangal Soğuk Çekilmiş

Yuvarlak
Altıköşe
Kare

 2-22
3-12
4-12		 Parlak
Fosfatlı		 EN 10278
h9
h10
h11
  Uygulama Profil Aralık
[mm]		 Yüzey Tolerans
Çubuk Sıcak Haddelenmiş Yuvarlak 20-200 İşlem Görmemiş
Kabuk Soyulmuş		 –
Soğuk Çekilmiş Yuvarlak
Altıköşe
Kare		 3-70
3-70
4-60		 Parlak EN 10278
h9
h10
h11
Kabuk Soylumuş
Sıcak Haddelenmiş		 Yuvarlak 20-100 Parlak EN 10278
h9
h10
h11
Taşlanmış Yuvarlak 50-60 Parlak EN 10278
h7
h8
h9
h10
h11
Kangal Soğuk Çekilmiş

Yuvarlak
Altıköşe
Kare

 2-22
3-12
4-12		 Parlak
Fosfatlı		 EN 10278
h9
h10
h11

Ürünler

Kalite WNr. Açıklama Pdf
E335+S
E335GC		 1.0060
1.0543		 Carbon steel derived from the E335 type of the standard EN 10025-2; the addition of sulfur confers greater machinability by chip removal. Not suitable for hardening heat treatments.
S235JR
S235JRC		 1.0038
1.0122		 This basic steel with a low carbon content, present in the regulations since the beginning of the varied standards (Aq37, Fe37, Fe360, S235), is still widely used thanks to its versatility as it can be welded, bent, deformed, and worked in a variety of ways. Not suitable for heat treatments.
S355J2
S355J2C		 1.0577
1.0579		 Carbon steel present in the European standard EN 10025-2 as S355, it has a very high resilience even at low temperatures. Widely used for the production of flanges and fittings and for construction in general. Not suitable for hardening heat treatments.
Quality WNr. Description Pdf
C4C 1.0303 Steel with a very low carbon content, intended for the cold forming of very deformed and difficult-to-obtain small parts.
C10C 1.0214 Low carbon steel with a chemical composition specially designed for cold deformation. The pieces obtained are generally subjected to carburization and tempering.
100Cr6 1.3505 Base steel for the production of balls, rollers and rings for bearings, and for all small parts that must be subjected to localized and repeated loads. The high carbon and chromium content allows high hardness and perfectly transformed structures to be obtained after tempering. When it must be machined by chip removal or cold deformation, it must always be provided at the globulization annealing state.
Kalite WNr. Açıklama Pdf
A105
K105		 – A carbon steel in accordance with US standards, it has a very high resilience even at low temperatures. Used for flanges, fittings, and construction in general.
42CrMo4 1.7225 Steel produced at the quenched and tempered state according to the United States standard ASTM A-193, widely used for linkages and bolts destined for the oil industry. It is analytically similar to 42CrMo4 of the European standard. This version is produced at higher temperatures, has slightly lower resistance characteristics but greater plasticity.
A193
B16		 – A steel produced at the quenched and tempered state according to the United States standard ASTM A-193, it is used for linkages and bolts destined for the oil industry. Analytically similar to the 40CrMoV4-6 type of the European standard EN 10269. It has greater temperability than the previous type thanks to the higher amount of alloy elements.
42CrMo4 1.7225 A steel produced at the quenched and tempered state according to the United States standard ASTM A-193, it is used for linkages and bolts destined for the oil industry. Analytically similar to the 40CrMoV4-6 type of the European standard EN 10269. It has greater temperability than the previous type thanks to the higher amount of alloy elements.
Kalite WNr. Açıklama Pdf
E335+S
E335GC		 1.0060
1.0543		 Carbon steel derived from the E335 type of the standard EN 10025-2; the addition of sulfur confers greater machinability by chip removal. Not suitable for hardening heat treatments.
S235JR
S235JRC		 1.0038
1.0122		 This basic steel with a low carbon content, present in the regulations since the beginning of the varied standards (Aq37, Fe37, Fe360, S235), is still widely used thanks to its versatility as it can be welded, bent, deformed, and worked in a variety of ways. Not suitable for heat treatments.
S355J2
S355J2C		 1.0577
1.0579		 Carbon steel present in the European standard EN 10025-2 as S355, it has a very high resilience even at low temperatures. Widely used for the production of flanges and fittings and for construction in general. Not suitable for hardening heat treatments.
Quality WNr. Description Pdf
C4C 1.0303 Steel with a very low carbon content, intended for the cold forming of very deformed and difficult-to-obtain small parts.
C10C 1.0214 Low carbon steel with a chemical composition specially designed for cold deformation. The pieces obtained are generally subjected to carburization and tempering.
100Cr6 1.3505 Base steel for the production of balls, rollers and rings for bearings, and for all small parts that must be subjected to localized and repeated loads. The high carbon and chromium content allows high hardness and perfectly transformed structures to be obtained after tempering. When it must be machined by chip removal or cold deformation, it must always be provided at the globulization annealing state.
Kalite WNr. Açıklama Pdf
A105
K105		 – A carbon steel in accordance with US standards, it has a very high resilience even at low temperatures. Used for flanges, fittings, and construction in general.
42CrMo4 1.7225 Steel produced at the quenched and tempered state according to the United States standard ASTM A-193, widely used for linkages and bolts destined for the oil industry. It is analytically similar to 42CrMo4 of the European standard. This version is produced at higher temperatures, has slightly lower resistance characteristics but greater plasticity.
A193
B16		 – A steel produced at the quenched and tempered state according to the United States standard ASTM A-193, it is used for linkages and bolts destined for the oil industry. Analytically similar to the 40CrMoV4-6 type of the European standard EN 10269. It has greater temperability than the previous type thanks to the higher amount of alloy elements.
42CrMo4 1.7225 A steel produced at the quenched and tempered state according to the United States standard ASTM A-193, it is used for linkages and bolts destined for the oil industry. Analytically similar to the 40CrMoV4-6 type of the European standard EN 10269. It has greater temperability than the previous type thanks to the higher amount of alloy elements.

    Etiam magna arcu, ullamcorper ut pulvinar et, ornare sit amet ligula. Aliquam vitae bibendum lorem. Cras id dui lectus. Pellentesque nec felis tristique urna lacinia sollicitudin ac ac ex. Maecenas mattis faucibus condimentum. Curabitur imperdiet felis at est posuere bibendum. Sed quis nulla tellus.

    ADDRESS

    63739 street lorem ipsum City, Country

    PHONE

    +12 (0) 345 678 9

    EMAIL

    info@company.com

    PURCHASE